How to Build a DIY Table: 4 Tips for Building a Table

Making your own table is a fun and easy DIY project, but it does require planning. Something like a [DIY nightstand](https://www.masterclass.com/articles/diy-nightstand-guide) is slightly easier than building a dining table, so if you’re a beginner, consider starting small. 1. __Plan out your design__. Like you would with any woodworking project, you should make a rough sketch of your DIY table plans before you begin building. Use a ruler or tape measure to make sure your dimensions are drawn to scale. 2. __Choose the right wood for your project__. Pine is a beginner-friendly wood that is sturdy but inexpensive. For outdoor projects (like a picnic table or patio table), consider redwood, cypress, or a pressure-treated pine. You can even use reclaimed wood or [live edge wood](https://www.masterclass.com/articles/how-to-finish-a-live-edge-wood-slab-for-rustic-furniture) for the top of a farmhouse dining table. Factory pallets are usually made from oak or pine. Hypertufa is a combination of cement, peat moss, and perlite that weighs less than concrete and makes an excellent tabletop that doesn’t require sealing. 3. __Consider pre-cutting your wood__. If you plan your design out before you start your project, you will know the dimensions of the wood you need. This means that you can ask your hardware store to cut the pieces of wood for you, reducing your building time. 4. __Ask for help__. Your finished product will likely end up being heavy. It’s a good idea to have someone there to help you flip your table over when it’s done. Certain table designs will require different components, but below are just some of the materials you will need when crafting your own wood dining table. 1. __Lumber__: For a simple wooden dining room table, you will need four table legs made of 4 x 4 inch blanks. Your legs may also be made from a different material like steel hairpin legs which are sold at most hardware stores. If using your own lumber for your tabletop, prepare. four to five two-inch by 10-inch wooden boards. You can sand these with 220-grit sandpaper on an electric sander. 2. __Woodworking Tools__: If you need to cut your own lumber, you will need a table saw, miter saw, or circular saw. You will also need wood glue and clamps to help keep your pieces of lumber together as you work. You’ll need sandpaper, and wood stain to finish your table. 3. __Household tools and hardware__: For this project, you will need a power drill and driver bits, an electric sander, and a pocket hole jig—a tool that makes drilling hidden (pocket) holes easier. You’ll also need a number of screws to screw your tabletop support and legs together, and a tape measure to document your table dimensions. 4. __Safety supplies__: Every time that you cut wood, you should wear gloves, safety goggles, and a filtered mask. When you have your materials and tools together, it’s time to start putting your kitchen table together. Follow these steps for building your own DIY dining table. 1. __Make your building plans__. Before you start building your table, you should sketch out plans for it. Measure out how large you want your table to be, noting the dimensions in your sketch. You should be noting the size of your tabletop, your legs, and your table “apron” which will serve as a support system for your tabletop to attach the table legs to. 2. __Cut your lumber__. You can purchase pre-cut lumber for the pieces you’ll need to make your table. If you are cutting your own lumber, make sure to wear goggles, a mask, and gloves when you do so. Cut your four wooden planks to a length of 29 ½ inches for your legs. For the tabletop, cut two 10-inch wooden planks, or simply sand down a large piece of reclaimed wood. Cut the lumber that will become your apron by cutting two planks of wood to the width of your tabletop, and two pieces to the length of your tabletop. 3. __Build your tabletop__. Lay your tabletop boards side by side on a flat surface facing down so that you can work on the bottom of your tabletop. Create angled pocket holes with your pocket hole jig on the wide sides of your planks, angled into the edge grain where your pieces of lumber will be fused together. Glue the edge grains with the pocket holes of planks together, then secure them with 2 ½ inch pocket hole screws. 4. __Add your aprons__. Cut four 2 x 4 pieces of wood to the size of your table. Create angled pocket holes with your pocket hole jig on top of the plank, near the edge grain of the wood. Clamp and glue these together using standard wood glue, and then fasten the apron together with screws. Make sure your pocket holes are placed on the nearer side of the table. Glue your apron to the bottom of your tabletop, then fasten the pieces together with pocket screws. 5. __Attach your legs__. Glue your table legs to the inside corners of the table’s apron. Secure these with fastening screws. Make sure your legs are at a right angle to the tabletop before screwing them into place to prevent your table from wobbling. 6. __Sand and stain__. Sand down your tabletop and the legs, going with the grain of the wood. In a well-ventilated area, apply a wood staining finish with a brush. Wipe up the excess stainer with a rag and apply a second coating after the first stain dries. For outdoor tables, consider using a sealant or a coat of water-proof polyurethane to protect it from the elements. Master everything from color theory to pattern mixing with the [MasterClass Annual Membership](https://www.masterclass.com) and exclusive lessons from award-winning interior designers like Kelly Wearstler and Corey Damen Jenkins. From shopping for statement furniture to designing a lighting scheme to choosing the newest member of your plant family, the skills you’ll pick up are sure to make your house, apartment, or condo feel even more like a home. Learning how to build a table may seem complicated, but the right supplies, instructions, and plan can set you up for success. This tutorial offers step-by-step instructions on how to build it.